The ANAN-8000DLE HF & 6M 200W SDR Transceiver meets and exceeds
the requirements of even the most discerning Amateur Radio Operator, it
is based on the work of the OpenHPSDR community.

Please note that output on HF bands may well exceed 200Ws, it is
recommended that the User cap the output at 200Ws, on 6M it is normal to
have maximum output between 175-200W.

Keeping in mind the various requirements posed by new cutting edge
technologies implemented in the radio it has been designed from scratch,
the design successes of the previous generation hardware has been
improved in the new implementation.

The ANAN-8000DLE uses an entirely new redesigned transmit chain
keeping in mind PureSignal (Predistortion), the result is astounding IMD
performance, the typical transmit IMD distortion is about a 1000 times
lower than that achieved by a typical modern transceiver available
today. It is the world’s first Amateur Radio transceiver to use a 50v
LDMOS device in the finals.

The ANAN-8000DLE includes two phase synchronous front ends to enable Diversity reception,

An internal four phase low noise boost supply is used to convert
13.8v to 50v for the finals, this enables the user to have the
flexibility of using industry standard 13.8v DC as well as battery power
whilst at the same time the radio provides all the advantages of the
50v LDMOS amplifier.

The front panel Display is microprocessor driven and displays all
critical parameters such as Forward and Reflected Power, SWR, Current,
Voltage, Temperature. The microprocessor also provides real time
protection for all these parameters.

---

General Specifications:

Architecture: Direct Sampling DDC/DUC TransceiverInterface: EthernetPhase Noise (Clock): -149dB @ 10KhzTCXO Stability (Typical): /- .1 PPMModes: CW, SSB, NFM, AM, DigitalAntenna Ports: Three SO-239 50 ohms Software Configurable Ports, One BNC for RX2Frequency Resolution: 1 Hz

 

Electrical Specifications:

13.8v DC @ 35A, 3A Receive/35A Transmit

 

Mechanical Specifications:

12Kg (approx. Weight)Dimensions: 483MM (L)  x 123MM (H) x  320MM (D) (Not including extrusions)Stainless Steel Chassis and Aluminum Heatsink

 

Receiver Specifications:

Receiver Architecture: Direct Down ConversionDual 16 bit Phase Synchronous ADCsIndependent filter banks for each ADC10/6M LNAsFrequency Coverage: 9Khz to 60MhzAttenuator: 1-30dB step attenuatorReciprocal Mixing Dynamic Range (RMDR): 116dB @ 2KhzReceiver Phase noise: -149dB @ 10KhzImage rejection: 100dBHardware support for 7 independent receivers assignable to either ADC

 

Transmitter Specifications:

Transmitter Architecture: Direct Up ConversionDAC Resolution: 16 bitRF Output Power: 200W SSB, CW, FM, RTTY, Digital; 1-50W AM, 6M 175-200W SSB, CW, FM, RTTY, Digital; 1-50W AMIMD: IMD3 typically -72dB @ 200W output on 20MHarmonics: Typically better than -50dBc on HF and -60dBc on 6MCarrier and Opposite Sideband Suppression: Better than -80dBcTransverter IF Output: 0db to 15dB

 

IOs:

RCA Line In, Line Out, PTT in, PTT OutDB9 Seven Software configurable Open Collector OutputsBNC XVTR TX Out, 10Mhz Reference Input6.25mm Barrel Mic, CW Key, Headphones and Speaker OutputsSMA PureSignal (Predistortion) Loop Input and OutputRJ45 Ethernet LAN Connector